Registar
Condições de filtragem
  • Estoque
  • I.D. d(φ)
  • O.D. D(φ)
  • Width B (or T)(mm)
  • Basic Load Rating Cr (Dynamic)(N)
  • CAD
  • Dias de envio estimados
    • Tudo
    • Envio possível no próprio dia
    • Dentro de 5 dias úteis
    • Dentro de 7 dias úteis
  • Deep groove ball bearings / single row / ZZ / stainless, EN 1.4301 equiv. / MISUMI

    Número da peça:

    Indefinido. 13 candidatos encontrados.
    Quantidade:

    Desenho de contorno e tabela de especificações

    Back to the Category Ball Bearings

    Technical Drawing - Ball Bearings

     

    EN 1.4301 Equiv. Ball Bearings:Related Image

    Available dimensions and tolerances can be found under the tab More information.

     

    Basic Properties (e.g., material, hardness, coating, tolerance) - Ball Bearings

     

    Operating Temperature: -40 ~ +150°C
    EN 1.4301 Equiv. may be slightly magnetized after machining.

     

    ComponentMaterial
    Inner/Outer Rings, Shield,
    Retainer, Ball
    EN 1.4301 Equiv.

    For further specifications please see the More information tab.
    Information on tolerances and rotational accuracy of the radial bearings can be found in the following PDF: Ball bearing table / tolerances as PDF

     

    Composition of a Product Code  - Ball Bearings

     

    Part Number
    SUB6000ZZ
    3NC6000ZZST
     
    General Information - Ball Bearings

     

    Ball bearing - deep groove ball bearing - axial bearing - axial ball bearing - axial groove ball bearing - angular ball bearing - spherical ball bearing - tension bearing

     

    Ball Bearing Selection Details

    - Ball material: steel, stainless steel, ceramic, plastic, glass, chrome-plated

    - Type of bearings: axial ball bearings, thin section bearings, spherical ball bearings, deep groove ball bearings, single-row angular ball bearings, double-row ball bearings, tension bearings, four-point bearings

    - Outer ring: flat, spherical, with flange, annular groove, U-groove, V-groove

    - Properties: heat-resistant, non-magnetic, corrosion-resistant, dust-proof, vacuum, high speed

    - Inner diameter: 2 mm to 50 mm

    - Outer diameter: 5 mm to 110 mm
     

    Ball bearing designation (suffix):

    In addition to the dimensional designation of the ball bearing, ball bearings often also have a designation for a cover disc or sealing disc. The following names are the most common names of various manufacturers that can be selected in the MISUMI online shop.
     

    - Double-sided sealing washer: 2RSH/2RS1, 2RSR/C-2HRS, DDU/DD
    - Single-sided sealing washer: RSH/RS1, RSR/C-HRS, DU
    - Double-sided sealing washer with low friction: 2RSL/2RZ/VV
    - Double-sided cover disc: 2Z/ZZ, 2ZR/C-2Z
    - Single sided cover disc: Z, ZR/C-Z/Z
     

    Description/Basics

     

    Rolling bearings

    Rolling bearings are generally divided into ball bearings and roller bearings. Ball bearings are a popular type of rolling bearings due to their high permissible speed and low friction.
    In the MISUMI online shop, you can purchase ball bearings that can be customized to your applications and environmental conditions. Our ball bearings are available in different materials and in a combination of different materials (hybrid bearings). In addition, MISUMI offers ball bearings already integrated into the housing as bearing housing.

     

    Grooved ball bearings

    Grooved ball bearings are the most commonly used rotary rolling bearings. This type of ball bearing is ideally suited for supporting rotating machine elements. A grooved ball bearings are intended for load bearing of radial forces and light axial forces. Grooved ball bearings are designed for high speeds and are used in a wide variety of industrial applications and designs. MISUMI already offers ball bearings integrated into housings and holders as bearing housings.

     

    Areas of Application


    Ball bearing - chemical resistance

    Chemical resistance

    Plastic ball

    Metal ball

    Ceramic ball

    Bearing rings

    UHMW

    PEEK

    PTFE

    EN 1.4125 equivalent

    EN 1.4301 equivalent

    EN 1.4125 equivalent

    EN 1.4542 equivalent

    Cover plate

    -

    -

    -

    EN 1.4301 equivalent

    EN 1.4301 equivalent

    EN 1.4301 equivalent

    EN 1.4301 equivalent

    Bearing balls

    Glass

    Ceramic
    (aluminum oxide)

    Ceramic
    (aluminum oxide)

    EN 1.4125 equivalent

    EN 1.4301 equivalent

    Ceramic

    Ceramic

    Ball cage

    UHMW

    PEEK

    PTFE

    EN 1.4301 equivalent

    EN 1.4301 equivalent

    Fluoroplastic

    Fluoroplastic

    Acids

    Hydrochloric acid

    suitable to a limited extent

    good

    very good

    unsuitable

    good

    suitable to a limited extent

    good

    Sulfuric acid

    suitable to a limited extent

    good

    very good

    unsuitable

    very good

    good

    very good

    Nitric acid

    suitable to a limited extent

    good

    very good

    unsuitable

    very good

    good

    very good

    Bases

    unsuitable

    very good

    very good

    unsuitable

    very good

    good

    very good

    Solvents

    very good

    very good

    very good

    unsuitable

    very good

    good

    very good

    Salt water

    very good

    very good

    very good

    unsuitable

    very good

    good

    very good

    Water

    very good

    very good

    very good

    unsuitable

    very good

    very good

    very good

    Comparison Table The ball bearing comparison table is provided for comparison purposes only (consider the lubricant and the sealing washer separately).
     

    Ball bearing materials

    In the MISUMI online shop, ball bearings are available in cost-effective rolling bearing steel, corrosion-resistant stainless steel and stainless steel. Furthermore, our product range includes various hybrid bearings in the following combinations: metal & ceramic, plastic & ceramic, plastic & glass.

    Our various materials offer good resistance to various environmental influences. Our ball bearing shop includes the ball materials stainless steel, steel, UHMW, PEEK, PTFE, ceramic and glass.

     

    Instructions for Use / Installation Information - Ball Bearings

     

    Installation Information

    An incorrect assembly and disassembly can damage a ball bearing. Therefore, a suitable tool must always be used to assemble and disassemble ball bearings or roller bearings.
    Ball bearings should not be assembled with a hammer, as this can deform the ball bearing. It is recommended using a suitable press. During pressing, the contact surface can be provided with lubricant to protect the surfaces and facilitate assembly.
    It is best to use a bearing puller for disassembly.

     

    Maintenance

    The ball bearing in roller bearings should be inspected for damage during maintenance.
    Before regreasing, a ball bearing should first be thoroughly cleaned.
    Remaining contamination in the bearing can damage the ball bearing. As a rule, a ball bearing should not be completely filled with grease, as this can cause the bearing to heat up too much and can cause it to fail.
    For encapsulated and sealed ball bearings, it is recommended to replace the bearing. Maintenance is not recommended due to the risk of damage to the cover place or seal.
     

    Supplementary Article

     

    Bearing Lock Nuts

    Shaft nuts - lock nuts - steel shaft nut - stainless steel shaft nut - shaft with retaining nut - shaftnNut with clamp screw - shaft nut with grub screw - shaft assembly

     

    Bearings with Housing

    Bearing with housing - bearing housing - bearing units - ball bearing holder - ball bearing with housing - bearing housing with flange - shaft holder with ball bearing

     

    Axles / Rotary Shafts

    Rotary axis - offset rotary shaft - double offset shaft - female threaded shaft - keyway shaft

     

    Drive shafts

    Motor shaft - torsion shaft - shaft with collar - shaft with shoulder - offset shaft - keyway shaft

     

    Plain Bearing (Bushes)

    Plain bearing - maintenance free - plain bearing bushings - plain bearing bushing with collar - plain bearing bushing with flange - plastic bushing - plastic plain bearing bushing

     

    Industrial Applications

     

    3D printer industry
    Automotive industry
    Pharmaceutical industry
    Packaging industry

     

    Lista de números de peça

    Número de itens

    I.D. d

    (φ)

    O.D. D

    (φ)

    Width B (or T)

    (mm)

    Basic Load Rating Cr (Dynamic)

    (N)

    Allowable Rotational Speed

    (1/min)

    Basic Load Rating Cor (Static)

    (N)

    RoHS?Quantidade mínima de encomenda
    10
    26
    8
    91
    1800
    59
    10
    1 unidades
    12
    28
    8
    102
    1500
    72
    10
    1 unidades
    15
    32
    9
    112
    1300
    85
    10
    1 unidades
    17
    35
    10
    120
    1200
    98
    10
    1 unidades
    20
    42
    12
    188
    1000
    152
    10
    1 unidades
    8
    22
    7
    66
    2000
    41
    10
    1 unidades
    10
    30
    9
    102
    1500
    72
    10
    1 unidades
    12
    32
    10
    136
    1500
    92
    10
    1 unidades
    15
    35
    11
    153
    1300
    113
    10
    1 unidades
    17
    40
    12
    192
    1100
    144
    10
    1 unidades
    20
    47
    14
    256
    900
    200
    10
    1 unidades
    6
    19
    6
    52
    2100
    32
    10
    1 unidades
    8
    24
    8
    67
    1900
    42
    10
    1 unidades
    Preço unitário (excluindo IVA)(Preço unitário incluindo IVA)
    Data de envio standard
    30.60 €
    ( 36.41 € )
    Item em stock - 1 dia útilDisponível para envio no próprio dia
    31.35 €
    ( 37.31 € )
    5 dias úteis
    34.38 €
    ( 40.91 € )
    5 dias úteis
    37.40 €
    ( 44.51 € )
    5 dias úteis
    41.68 €
    ( 49.60 € )
    5 dias úteis
    32.62 €
    ( 38.82 € )
    7 dias úteis
    31.99 €
    ( 38.07 € )
    5 dias úteis
    35.52 €
    ( 42.27 € )
    5 dias úteis
    39.55 €
    ( 47.06 € )
    5 dias úteis
    42.82 €
    ( 50.96 € )
    5 dias úteis
    53.40 €
    ( 63.55 € )
    5 dias úteis
    32.62 €
    ( 38.82 € )
    5 dias úteis
    33.37 €
    ( 39.71 € )
    5 dias úteis

    Informações detalhadas

    Informações básicas

    Contorno e especificações

    Back to the Category Ball Bearings

    Technical Drawing - Ball Bearings

    EN 1.4301 Equiv. Ball Bearings:Related Image

     

    Specification Tables - Ball Bearings
     
    Part Numberd D B r
    (min)
    Basic Load RatingAllowable Rotational Speed
    rpm
    (Reference)
    Relative DimensionsMass
    (g) (Reference)
    Unit Price
    ToleranceToleranceToleranceCr (Dynamic) NCor (Static) NDsdh
    (max)
    R
    (max)
    (min)(max)
    SUB626ZZ6+0.05
    0
    190
    -0.03
    60
    -0.12
    0.352322100810170.38.2 
    SUB608ZZ8227664120001011.52012 
    SUB628ZZ24867421900122218 
    SUB6000ZZ1026915918001213.52419 
    SUB6200ZZ3090.61027215001416260.632 
    SUB6001ZZ122880.30.321 
    SUB6201ZZ320
    -0.035
    100.6136921617280.637 
    SUB6002ZZ1590.311285130017193030 
    SUB6202ZZ35110.615311319203146 
    SUB6003ZZ17100.3120981200213341 
    SUB6203ZZ40120.6192144110021223666 
    SUB6004ZZ2042188152100024253868 
    SUB6204ZZ47141.02562009002527421.0105 
    kgf=Nx0.101972

    More Information

    Performance Comparison of Bearings for Special Environment
    Part NumberInner/Outer RingsShieldRolling ElementRetainerLow Dust GenerationAbrasion ResistanceCorrosion Resistance and Chemical ResistanceHeat ResistanceVacuumInsulationNon-magneticHeavy LoadHigh Rotational Speed
    AcidAlkaliSolventSeawaterWater
    Hydrochloric AcidSulfuric AcidNitric Acid
    SE6□□□ZZPREN 1.4125 Equiv.
    Special Fluoro-Macromolecule Coating
    EN 1.4301 Equiv.EN 1.4125 Equiv.
    Special Fluoro-Macromolecule Coating
    EN 1.4301 Equiv.
    Special Fluoro-Macromolecule Coating
    ××××××××
    (-100~200°C)
    ×××
    3NC6□□□ZZSTEN 1.4125 Equiv.EN 1.4301 Equiv.CeramicsFluororesin×
    (-100~200°C)
    ×××
    3NC6□□□ZZMDEN 1.4542 Equiv.EN 1.4301 Equiv.CeramicsFluororesin×
    (-100~200°C)
    ××
    SUB6□□□ZZEN 1.4301 Equiv.EN 1.4301 Equiv.EN 1.4301 Equiv.EN 1.4301 Equiv.×
    (-40~150°C)
    ××××
    The service life may be shortened drastically when used in conditions where the product is soaked in corrosive solution.
    (◎Well Suited ○Good △Questionable ×Not Suitable)