Rack gears / induction hardened / ground / contact angle 20 degrees modules 1.0 / 1.5 / 2.0 / 2.5 / 3.0 (RGEAH1.5-300-N)

Rack gears / induction hardened / ground / contact angle 20 degrees modules 1.0 / 1.5 / 2.0 / 2.5 / 3.0 RGEAH1.5-300-N

Click on this image to zoom in.

Click on this image to zoom in.

  • Promotional pricing ends 31/12/2024

Product Details:

Manufacturer part number: RGEAH1.5-300-N

Brand: MISUMI

Price: 88.57

Delivery time: 5 Days


Technical Data:

Module (M) / Circular Pitch (P): 1.5

Length L: 296.85 mm

Number of Effective Teeth: 63 teeth

Tooth Width W (or D): 15 mm

Rack Height: 20 mm


  • Order quantities extended (D-JIT)

Data sheet

Unit еxample related to this product

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

RGEAH1.5-300-N

Back to the Category Rack Gear

Technical drawing - Rack Gears

Rack Gears/Induction Hardened/Ground/Pressure Angle 20deg./Module 1.0/1.5/2.0/2.5/3.0:Related Image
Open the technical drawing in the new window

 

Available dimensions and tolerances can be found under the tab More Information.

Basic properties (e.g., material, hardness, coating, tolerance) - Rack Gears

TypeMaterialSurface TreatmentHardness
RGEAHEN 1.1191 Equiv.Black OxideTooth Induction Hardened
45~55HRC
Teeth and Hole Machined surfaces have no surface treatment.

Further specifications can be found under the tab More Information.

Composition of a product code - Rack Gears

Part Number-Nominal-Hole Machining
RGEAH1.0 -500-A

Alterations - Rack Gears

Rack Gears/Induction Hardened/Ground/Pressure Angle 20deg./Module 1.0/1.5/2.0/2.5/3.0:Related Image

General information - Rack Gears

Rack gear product assortment - steel rack gear - stainless steel rack gear - brass rack gear - plastic rack gear - hardened rack gear

 

Selection Details of Rack Gears

-Material: steel, stainless steel, brass, plastic

-Coatings: uncoated, burnished

-Heat treatment: untreated, surface curing (induction hardened)

-Module: 0.5, 0.8, 1, 1.5, 2, 2.5, 3

-Width: 3 to 30 mm

-Number of teeth: 9 to 192

-Outer diameter (round): 8 to 30 mm

-Length: 20 to 1980 mm

 

Description / Rack Gear Basics

The rack gear from MISUMI are fundamentally used for motion conversion. The rack gear allows converting a rotary motion into a linear motion or a linear motion into a rotary motion. A rack gear can transmit high forces due to the form-fitting gearing. In connection with a gear wheel or spur gear, a gear rack drive forms a slip-free transmission of force and prevents a slip-through. For a large number of applications, the slip-free transmission of the rack gear is an efficient transmission of force and motion. The rack gear drive also withstands high loads with a compact design. With rack gears, high speeds can also be driven in applications with low noise generation. With MISUMI, you can configure your rack gears individually in length and in other parameters.

During the transfer of motion, the teeth intertwine and largely unroll during the transfer to one another. The rack gear can be used for the transfer of motion almost over the entire length. To prevent the gear wheel from overflowing, for example, stopper bolts or stopper blocks are recommended. Since the module is standardized, it must be ensured for the construction of a rack drive that the same module is used for the rack and the gear wheel. The rack gear allows precise control by directly transmitting motion, torque and speed.

For high wear resistance and reliability, our product range also offers surface-hardened rack gears. The hardened rack gear has a harder surface of the teeth, which makes it less susceptible to wear and tear. Their long service life helps reduce production downtime. Hardened rack gears are also less susceptible to locking-related play and retain their precision in the long term. This aspect makes hardened rack gears particularly recommended for precise applications.

A rack gear drive has a low backlash. In general, the tooth flank clearance is used for assembly and thermal expansion. Like the head play, it can serve as a gap for lubricants. For very precise applications, the reverse play is not beneficial. In order to minimize this during precision applications, pre-tensioning is required. On lifting tables, the dead weight already generates a vertical pretension in the rack gear, which minimizes the reverse play. If the rack gear is aligned horizontally, a separate pretension should be used to reduce the reverse play. This can be achieved with tension springs or other exciting components, for example. When selecting a suitable rack gear, the first decision criterion is the material of the rack gear drive. The following are some advantages of the rack gear materials:

 

Steel rack gears

Rack gears made of steel have high strength and withstand high loads. Therefore, steel rack gears are suitable for heavy loads. The material surface can be hardened to increase wear resistance. This makes the rack gear resistant and durable. In addition, steel is very heat-resistant and is suitable for applications in which high ambient temperatures occur. One disadvantage of steel is its low corrosion resistance.

 

Stainless steel rack gears

Stainless steel rack gears are highly corrosion resistant, since stainless steel forms a passive layer (oxide layer). This makes them suitable for applications where higher humidity is found. Furthermore, stainless steel offers good chemical resistance. Like steel, stainless steel is temperature resistant without losing strength. High temperatures can cause discoloration (tempering colour) in stainless steel. However, this does not affect the function in any way. Similar to the steel, stainless steel is robust and has a long service life. Another advantage is that rack gears made of stainless steel have hygienic properties. Therefore, this material is often used in the pharmaceutical industry and in medical technology.

 

Brass rack gears

Brass rack gears are well protected against corrosion. Therefore, a brass rack gear is well suited in corrosive environments. Depending on the application, it can be advantageous that brass does not tend to spark when abrasion is applied. In addition, brass has a high strength and ductility. This allows the material to deform before it breaks. Brass rack gears have a high thermal conductivity, which allows heat to be dissipated similar to a heat sink. The perhaps most important property of the brass rack gear is its gliding property. In the case of a lubrication film dissipates, this property serves as a certain fail-safe.

 

Lubrication of rack gears

The lubrication of the rack gear is decisive for low-wear operation. The lubrication reduces the friction on the tooth flanks of the rack gear and the pinion, which reduces the material abrasion. In this way, proper lubrication of the rack gear increases the service life, performance and ensures long-term precision. In principle, a rack can be lubricated with grease or oil. The type of lubrication that is suitable depends on several factors such as temperature, load and speed. Grease lubrication is often used for high loads and torques, while oil lubrication is used for high speeds. Lubricant manufacturers offer a suitable lubricant for almost all load cases. Before re-lubricating, the tooth drive should be thoroughly cleaned to prevent damage to the tooth flanks or teeth from contamination. Depending on the application, the lubricant can be sprayed, brushed, or sprayed onto the rack gear. The lubrication intervals must be selected depending on the application and the lubricant used. It is always recommended to adjust the lubrication intervals to the given circumstances.

 

Application examples - Rack Gears

Application example: rack gear - round rack gear - rack gear with spur gear - rack gear with pinion - rack gear with handle

Application example - rack gear with spur gear
(1) Spur gear, (2) Clamping knobs, (3) Rack gear

 

Industrial applications

3D printer industry
Automotive industry
Pharmaceutical industry
Packaging industry

Part Number:  

    3D preview is not available, because the part number has not yet been determined.

  • In order to open the 3D preview, the part number must be fixed.
Loading...
Part Number
RGEAH1.5-300-N
Part Number
Standard Unit Price
Minimum order quantityVolume Discount
Standard
Shipping Days
?
RoHSModule (M) / Circular Pitch (P) Length L
(mm)
Number of Effective Teeth
(teeth)
Tooth Width W (or D)
(mm)
Rack Height
(mm)
Hole Machining Tapping Alteration on End

88.57 €

1 5 Days 101.5296.85631520N (No Hole machining)No Alteration

Loading...

  1. 1

Back to the Category Rack Gear

Technical drawing - Rack Gears

Rack Gears/Induction Hardened/Ground/Pressure Angle 20deg./Module 1.0/1.5/2.0/2.5/3.0:Related Image
Open the technical drawing in the new window

 

Available dimensions and tolerances can be found under the tab More information.

Specification Tables - Rack Gears

Part NumberNominalHole MachiningNumber of Effective TeethLP (Pitch)WHhB
(Hole Pitch)
M (Coarse)d1d2Z1K
(Number of Holes)
TypeModule
RGEAH1.0 300N
(No Hole Machining)
A
(Bottom Tapped)
ST
(Side Tapped)
Z
(Side Counterbored)
95298.453.142101211180M33.56.53.52
500159499.513
1.5 30063296.854.712152018.5180M44.584.52
500106499.513
2.0 50079496.376.283202523180M55.59.55.53
2.5 50063494.87.854253027.5180M55.59.55.53
3.0 50053499.519.424303532180M55.59.55.53

Alterations - Rack Gears

 

Rack Gears/Induction Hardened/Ground/Pressure Angle 20deg./Module 1.0/1.5/2.0/2.5/3.0:Related Image

Basic information

Tooth Type Standard Shape Rack Gears Heat Treatment High Frequency
Ground Tooth Provided Surface Treatment Black Oxide End Face Machining Both Ends Machined Type

This page is Rack gears / induction hardened / ground / contact angle 20 degrees modules 1.0 / 1.5 / 2.0 / 2.5 / 3.0, part number RGEAH1.5-300-N.
You can find the detail information about specifications and dimensions on part number RGEAH1.5-300-N.

Frequently Asked Questions (FAQ)

Question:

What are rack gears for?

Answer:

Rack gears are machine elements that convert rotary motion into linear motion. This can also be done in reverse order. The rack gear can transmit high forces directly and without slip with a gear wheel.

Question:

What materials are used for rack gears?

Answer:

MISUMI’s rack gears are made of steel, stainless steel (stainless steel), brass and plastic. Each material offers different properties that must be selected to suit a wide range of requirements.

Question:

What types of rack gears do you offer?

Answer:

There are straight-toothed rack gears and slanted rack gears. The rack gears with straight gearing are often used to implement linear motion. The obliquely toothed rack gears are often used for conversion into a rotation.

Question:

How are rack gears lubricated?

Answer:

In most cases, a rack gear is lubricated with grease or oil. The appropriate lubricant should be used depending on the application (heavy loads, high temperature, high speed). For high-speed applications, oil is usually used. A grease is often used in heavy load applications.

Question:

What are the advantages of rack gears?

Answer:

Rack gears withstand high loads and have a long service life. At the same time, rack gears are very precise and easy to assemble.

Show more FAQ Close

Variation of this product

Part Number
RGEAH1.0-500-N
RGEAH1.0-500-N-MC4
RGEAH1.0-500-N-WMC6
RGEAH1.5-300-N-MC6
RGEAH1.5-500-N
RGEAH1.5-500-N-MC5
Part NumberStandard Unit PriceMinimum order quantityVolume DiscountStandard
Shipping Days
?
RoHSModule (M) / Circular Pitch (P) Length L
(mm)
Number of Effective Teeth
(teeth)
Tooth Width W (or D)
(mm)
Rack Height
(mm)
Hole Machining Tapping Alteration on End

115.13 €

1 5 Days 101499.511591012N (No Hole machining)No Alteration

120.20 €

1 7 Days 101499.511591012N (No Hole machining)mC (One End Tapped)

125.27 €

1 7 Days 101499.511591012N (No Hole machining)WmC (Both Ends Tapped)

93.63 €

1 7 Days 101.5296.85631520N (No Hole machining)mC (One End Tapped)

141.71 €

1 5 Days 101.5499.511061520N (No Hole machining)No Alteration

146.78 €

1 7 Days 101.5499.511061520N (No Hole machining)mC (One End Tapped)

Complementary Products

MISUMI Unit еxample related to this product

Tech Support

Technical Support
Tel:+49 69 668173-0 / FAX:+49 69 668173-360