Stainless Steel-Levelling feet, with and without rubber underlay

Stainless Steel-Levelling feet GN 41 are easy and very reasonably priced foot design variants.
The will be delivered mounted and are not removable.

• Stainless Steel characteristics
• Elastomer characteristics
• Load rating information

• Base plate, blank ground
  Stainless Steel AISI 304
• Threaded stem
  Stainless Steel AISI 303
• Hexagon nut ISO 4032
  Stainless Steel AISI 304
• Rubber cap, clipped on
  black, Santoprene® (TPE)
  80 ≈ Shore A
• Rubber underlay, vulcanised
  black, Perbunan® (NBR)
  70 ± Shore A
• RoHS compliant

External hexagon at the bottom	Wrench flat at the bottom	Hexagon socket at the top
M 8, M 10, M 12	M 16, M 20, M 24	Wrench flat at the bottom
	"not dipping" version	M 16, M 20, M 24

 

External hexagon at the top	Wrench flat at the bottom	External hexagon
Wrench flat at the bottom	M 16, M 20, M 24	Female thread
M 16, M 20, M 24		M 8, M 10, M 12, M 16, M 20

 

d1 GN 41	d2			d3	d4	h1	h3	h4	h5	h6	l4	l5	l6	m1	m2	s	A/F1	A/F2	A/F3	A/F4	A/F5	A/F6
40	M 8	M 10	M 12	5.4	-	2	11	-	-	3.5	-	-	-	-	30	1.5	17	-	-	-	-	-
40	M 16	-	-	5.4	-	2	-	17	14	3.5	-	-	-	-	30	1.5	-	12	8	-	-	-
50	M 8	M 10	M 12	6.6	-	2.5	11	-	-	4	-	-	-	45	38	2	17	-	-	-	-	-
50	M 16	-	-	6.6	-	2.5	-	17	14	4	-	-	-	45	38	2	-	12	8	-	-	-
60	M 8	M 10	M 12	6.6	-	2.5	11	-	-	4.5	-	-	-	50	48	2	17	-	-	-	-	-
60	M 16	-	-	6.6	24	2.5	-	17	14	4.5	45	45	29	50	48	2	-	12	8	10	12	20
80	M 8	M 10	M 12	8.5	-	3	12	-	-	5	-	-	-	70	64	2	17	-	-	-	-	-
80	M 16	-	-	8.5	24	3	-	18	15	5	45	45	29	70	64	2	-	12	8	10	12	20
80	M 20	-	-	8.5	30	3	-	18	15	5	56	56	37	70	64	2	-	15	10	13	16	24
80	M 24	-	-	8.5	35	3	-	21	18	5	67	67	42	70	64	2	-	19	12	17	20	30

The static load bearing capacity given in the table rests on a test series in which the load has been applied perpendicular to the base plate (without rubber underlay). For the values given in the table, the strain relief may result in minor deformations of the base plate.
Bending and buckling stress which oftenoccurs in practice results in a lower load bearing capacity of the adjustment spindle and may have to be taken into account.
Also, the spindle strength is assumed to be ≥ 500 N/mm².
The details given on strength are nonbinding guide values without any liability. In general, they do not constitute a warranty of quality.
The user must determine from case to case if a product is suitable for the intended purpose or use. Environmental factors may influence the stated value