Registar
Condições de filtragem

Limpar tudo

  • Estoque
  • R Size(mm)
  • Type
  • work material
  • Blade length (ℓ)(mm)
    [5-30/1mm unidades]
  • Number of flutes(sheet)
  • Coating
  • Ball End Mills (Carbide) (Machining Application: Engraving)

      • Carbide Solid Ball End Mill CSBE
        • Volume Discount

        EIKOSHA

        Carbide Solid Ball End Mill CSBE

        R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
        0.4 ~ 20BallGeneral Steel[◎] / Quenched and tempered steel[○] / Cast Iron[○] / Aluminum[◎] / Copper[◎]3 ~ 702-45 ~ 180-4 ~ 32
        Preço regular (excluindo IVA):
        103.57 €
        Data de envio regular:
        6 dias úteis
        Configurar
      • SSPB220 CBN Super Spiral Ball End Mill

          NS TOOL

          SSPB220 CBN Super Spiral Ball End Mill

          [Features]· Spiral ball shape used to improve sharpness of cutting edge. · The cutting edge shape used improves the chipping resistance of the cutting edge. · When the peripheral cutting edge makes contact with the cutting surface, chatter vibration occurs due to an increase in cutting resistance and this affects tool life and cutting surface quality. (This effect can be reduced by using a strong back taper shape.) Torsion angle: 20°
          Ler mais
          R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
          0.1 ~ 3BallGeneral Steel[○] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[◎]0.15 ~ 3.62Non-Coated50 ~ 700.3 ~ 184
          Preço regular (excluindo IVA):
          172.90 €
          Data de envio regular:
          6 dias úteis
          Configurar
        • TSC series carbide ball end mill, short model
          • Volume Discount
          • TS
          • General Steel
          • 2 Flutes
          • S (Short)

          MISUMI

          TSC series carbide ball end mill, short model

          [Features] -Good surface finish can be expected for the rough surface of the workpiece after machiningIt has a coating with high oxidation resistance and high hardness, and achieves long service life. Effective in high-speed machining and dry machining as coating properties-Can be reground. Please refer to the "Regrinding Service" page for application procedures, range of services, prices, etc.
          Ler mais
          R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
          0.05 ~ 10BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]0.2 ~ 252For High Hardness (Silicon Group)40 ~ 15015 ~ 753 ~ 20
          Data de envio regular:
          5 dias úteis
          Configurar
        • MRC Series Carbide Ball End Mill, for Heat-Treated Steel Machining, 2-Flute / Short Model
          • Volume Discount
          • MR
          • General Steel
          • 2 Flutes
          • S (Short)

          MISUMI

          MRC Series Carbide Ball End Mill, for Heat-Treated Steel Machining, 2-Flute / Short Model

          High-performance products with emphasis on the machined surface accuracy are available in the deferred prices of the conventional products!
          Ler mais
          R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
          0.1 ~ 10BallGeneral Steel[○] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[○] / High Hardness Steel: to HRC65[○] / Stainless Steel[○] / Cast Iron[◎]0.4 ~ 252MRC50 ~ 150-4 ~ 20
          Preço regular (excluindo IVA):
          18.61 €
          Data de envio regular:
          5 dias úteis
          Configurar
        • 2-Flute, Ball End, Miniature, CRN-EBD-3

            OSG

            2-Flute, Ball End, Miniature, CRN-EBD-3

            A series of bore-end small diameter radius mills with CRN coating to improve lubricity.. Well suited for detail work on copper electrodes and IT components.
            Ler mais
            R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
            0.1 ~ 1.5BallAluminum[○] / Copper[◎] / Resin[◎]0.4 ~ 82CrN40-3
            Preço regular (excluindo IVA):
            69.89 €
            Data de envio regular:
            6 dias úteis
            Configurar
          • 2-Flute, Ball End, Miniature, FX-MG-EBD-3

              OSG

              2-Flute, Ball End, Miniature, FX-MG-EBD-3

              The use of FX coating and high strength carbide allows a wide range of machining.Coated for steelStandard/Alternation category: Manufacturer's standard productNumber of blades (pcs.) 2Shaft diameter (mm) 3, Total length (mm) 40, Spiral angle: standard spiral (30 to 44°)R Accuracy (µm) ±10.
              Ler mais
              R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
              0.2 ~ 1.5BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[○] / Stainless Steel[◎] / Cast Iron[◎] / Aluminum[○] / Titanium[○] / Copper[○]0.8 ~ 82TiAlN40-3
              Preço regular (excluindo IVA):
              84.73 €
              Data de envio regular:
              6 dias úteis
              Configurar
            • 2-Flute, Ball End, CBN-SXB

                OSG

                2-Flute, Ball End, CBN-SXB

                Spiral ball blade with its own twist achieve deep cuts in acute sharpness and small diameter. CBN end mill that can be used in the cut of the Carbide
                Ler mais
                R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                0.2 ~ 1.5BallGeneral Steel[○] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[◎]0.3 ~ 1.82Non-Coated45 ~ 501.2 ~ 64 ~ 6
                Preço regular (excluindo IVA):
                125.12 €
                Data de envio regular:
                6 dias úteis
                Configurar
              • For Graphite, 2 Flutes, Ball End, Long Type, GF-EBDL

                  OSG

                  For Graphite, 2 Flutes, Ball End, Long Type, GF-EBDL

                  Cemented carbide with superior abrasion resistance adopted as a base material, achieving long-life graphite processing.
                  Ler mais
                  R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                  1 ~ 6BallGraphite[◎]20 ~ 1302Non-Coated100 ~ 20025 ~ 806 ~ 12
                  Preço regular (excluindo IVA):
                  132.60 €
                  Data de envio regular:
                  6 dias úteis
                  Configurar
                • Spherical Ball End FXS-EQD
                  • Volume Discount

                  OSG

                  Spherical Ball End FXS-EQD

                  Spherical cutting edge prevent chattering in the machining of standing wall. Machining undercut enabled.
                  Ler mais
                  R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                  0.5 ~ 6Spherical BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[○] / Stainless Steel[◎] / Cast Iron[◎] / Titanium[○]0.7 ~ 8.12TiAlN60 ~ 1105 ~ 606 ~ 12
                  Preço regular (excluindo IVA):
                  121.20 €
                  Data de envio regular:
                  6 dias úteis
                  Configurar
                • Spherical Ball End GX-EQD-SF

                    OSG

                    Spherical Ball End GX-EQD-SF

                    Ball end mills having spherical cutting tips developed for shrink fitting.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    10Spherical BallGeneral Steel[◎] / Quenched and tempered steel[◎] / Stainless Steel[◎] / Cast Iron[◎] / Aluminum[○] / Copper[○]152For General Steels (AlCrN, etc.)58-12
                    Preço regular (excluindo IVA):
                    142.46 €
                    Data de envio regular:
                    6 dias úteis
                    Configurar
                  • MSBH345 3-Flute Ball-End Mill for High-Hardness
                    • Volume Discount

                    NS TOOL

                    MSBH345 3-Flute Ball-End Mill for High-Hardness

                    Enables high-efficiency machining with little chatter through the adoption of a unique three-flute blade shape and variable distribution
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.5 ~ 3BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[◎] / Stainless Steel[○] / Aluminum[○] / Titanium[◎] / Copper[○] / Resin[○]1.5 ~ 103For High Hardness (Silicon Group)60 ~ 80-6
                    Preço regular (excluindo IVA):
                    96.47 €
                    Data de envio regular:
                    6 dias úteis
                    Configurar
                  • MSB230G2 MUGEN-COATING High Precision Profit Ball End Mill
                    • Volume Discount

                    NS TOOL

                    MSB230G2 MUGEN-COATING High Precision Profit Ball End Mill

                    The tuned Infinity coating sustains high precision machining for a long time
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.05 ~ 3BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / Stainless Steel[◎] / Aluminum[◎] / Titanium[○] / Copper[◎] / Resin[◎]0.1 ~ 102TiAlN50 ~ 80-4 ~ 6
                    Preço regular (excluindo IVA):
                    58.31 €
                    Data de envio regular:
                    6 dias úteis
                    Configurar
                  • Solid Ball End Mill SBEL
                    • Volume Discount

                    DIJET

                    Solid Ball End Mill SBEL

                    Ultrafine particle carbide alloy with excellent wear resistance ensures long tool life.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.5 ~ 15BallGeneral Steel[○] / Quenched and tempered steel[○] / Graphite[○]5 ~ 802Non-Coated45 ~ 150-4 ~ 32
                    Preço regular (excluindo IVA):
                    107.03 €
                    Data de envio regular:
                    8 dias úteis
                    Configurar
                  • Carbide Ball End Mill for Rib for Resin Processing PRB-2
                    • Volume Discount

                    KYOWA SEIKO

                    Carbide Ball End Mill for Rib for Resin Processing PRB-2

                    Blade shape has been given excellent sharpness for resin machining. Longer neck section for deep machining.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.1 ~ 2.5BallAluminum[◎] / Resin[◎]0.3 ~ 62-45 ~ 100-4 ~ 6
                    Preço regular (excluindo IVA):
                    74.90 €
                    Data de envio regular:
                    8 dias úteis
                    Configurar
                  • TSC series carbide ball end mill (R accuracy ±3μm)
                    • Volume Discount
                    • TS
                    • General Steel
                    • 2 Flutes
                    • S (Short)

                    MISUMI

                    TSC series carbide ball end mill (R accuracy ±3μm)

                    [Features] -Radius tolerance within 6 µm (compared to manufacturer's measurements), shank diameter tolerance h5 standard adopted. Optimal for high precision 3D machining of moulds with high quality tools with low quality variation-Seamless shape (sharpening from outer edge to centre of rounded blade in 1 process) is designed to create smooth cutting edge flank without steps.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    1.5 ~ 3BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]4.5 ~ 92For High Hardness (Silicon Group)60 ~ 90-6
                    Preço regular (excluindo IVA):
                    46.74 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TSC series carbide ball end mill (for shrink fit holder / R accuracy ±3 μm) 2-flute / stub model
                    • Volume Discount
                    • TS
                    • General Steel
                    • 2 Flutes
                    • B (Stub)

                    MISUMI

                    TSC series carbide ball end mill (for shrink fit holder / R accuracy ±3 μm) 2-flute / stub model

                    [Features] -Designed with optimum blade length, shank length and overall length considering processing with shrink fit holder-Radius tolerance within 6 µm (compared to manufacturer's measurements), shank diameter tolerance h5 standard adopted. High-precision tools with low quality variation are ideal for high-precision 3D machining of moulds-Sampless shape (sharpening from the outer edge to the centre of the rounded blade in one process) is designed to produce a smooth cutting edge without steps.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.3 ~ 2BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]0.6 ~ 42For High Hardness (Silicon Group)40-6
                    Preço regular (excluindo IVA):
                    64.20 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TSC series carbide ball end mill, for shrinkage fitting, 2-flute / stub model
                    • Volume Discount
                    • TS
                    • General Steel
                    • 2 Flutes
                    • B (Stub)

                    MISUMI

                    TSC series carbide ball end mill, for shrinkage fitting, 2-flute / stub model

                    [Features] -Compatible with shrink fit chucks for high precision machining-Designed with short flute length and overall length for shrink fit and emphasis on rigidityIt has coating with high oxidation resistance and high hardness, and achieves long service life. Effective in high-speed machining and dry machining as coating characteristics.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.2 ~ 6BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]0.4 ~ 122For High Hardness (Silicon Group)40 ~ 65-4 ~ 12
                    Preço regular (excluindo IVA):
                    24.07 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • XAL series carbide ball end mill, 2-flute / short model
                    • Volume Discount
                    • XAL
                    • General Steel
                    • 2 Flutes

                    MISUMI

                    XAL series carbide ball end mill, 2-flute / short model

                    XAL Series is the definitive choice for cost-sensitive customers
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.05 ~ 10BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[◎] / Aluminum[◎] / Copper[○/◎] / Resin[○]0.2 ~ 382For General Steels (AlCrN, etc.)40 ~ 160-3 ~ 20
                    Preço regular (excluindo IVA):
                    13.95 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • XAC series carbide ball end mill, 2-flute / short model
                    • Volume Discount
                    • TiAlN
                    • General Steel
                    • 2 Flutes
                    • S (Short)

                    MISUMI

                    XAC series carbide ball end mill, 2-flute / short model

                    [Features] All-purpose ball nose end mill with 2 cutting edges for a wide range of profiling-For rough machining of workpieces that are expected to have a good surface finish after machining-Can be reground. Please refer to the "Regrinding Service" page for information on application methods, range of services, prices, etc.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.2 ~ 12.5BallGeneral Steel[○] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]0.8 ~ 502TiAlN40 ~ 180-3 ~ 25
                    Preço regular (excluindo IVA):
                    23.35 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • XAC series carbide ball end mill, 2-flute / short, long shank model
                    • Volume Discount
                    • TiAlN
                    • General Steel
                    • 2 Flutes

                    MISUMI

                    XAC series carbide ball end mill, 2-flute / short, long shank model

                    [Features] -Ideal for high precision 3D machining of moulds due to high tool rigidity and excellent chip evacuation-For rough machining of the workpiece, a good surface finish can be expected after machining.-Long shank type, ideal for deep cavity milling-Can be reground. Please refer to the "Regrinding Service" page for information on application procedures, range of services, prices, etc.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    2 ~ 8BallGeneral Steel[○] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]8 ~ 302TiAlN100 ~ 250-4 ~ 16
                    Preço regular (excluindo IVA):
                    45.59 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TSC series carbide ball end mill, regular model
                    • Volume Discount
                    • TS
                    • General Steel
                    • 2 Flutes
                    • R (Regular)

                    MISUMI

                    TSC series carbide ball end mill, regular model

                    [Features] -Regular bridge length allows for many regrinding times-Can be regrinded. Please refer to the "Regrinding Service" page for application procedures, range of services, prices, etc.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.2 ~ 8BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]1.5 ~ 302For High Hardness (Silicon Group)50 ~ 14017 ~ 804 ~ 16
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TSC series carbide ball end mill, 2-flute / short, long shank model
                    • Volume Discount
                    • TS
                    • General Steel
                    • 2 Flutes
                    • S (Short)

                    MISUMI

                    TSC series carbide ball end mill, 2-flute / short, long shank model

                    [Features] -Long shank, ideal for deep cavity millingIt has a coating with high oxidation resistance and high hardness, and achieves long service life. Effective in high speed machining and dry machining as coating properties-Can be reground. Please refer to the "Regrinding Service" page for application procedures, range of services, prices, etc.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.5 ~ 12.5BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]2 ~ 302For High Hardness (Silicon Group)70 ~ 28015 ~ 803 ~ 25
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TSC series carbide ball end mill, 3-flute / short model
                    • Volume Discount
                    • TS
                    • General Steel
                    • 3 Flutes
                    • S (Short)

                    MISUMI

                    TSC series carbide ball end mill, 3-flute / short model

                    [Features] -The 3-edge shape is resistant to chattering and enables high feed rate-The surface of the workpiece is very well finished after machining.-The coating has high oxidation resistance and high hardness and achieves long service life. Effective in high-speed machining and dry machining as coating properties-Can be reground. Please refer to the "Regrinding Service" page for application procedures, range of services, prices, etc.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.5 ~ 10BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]2 ~ 253For High Hardness (Silicon Group)50 ~ 15015 ~ 756 ~ 20
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TSC series carbide ball end mill, 3-flute / regular model
                    • Volume Discount
                    • TS
                    • General Steel
                    • 3 Flutes
                    • R (Regular)

                    MISUMI

                    TSC series carbide ball end mill, 3-flute / regular model

                    [Features] -The 3-edge shape is chatter resistant and enables high feed-The coating has high oxidation resistance and high hardness and achieves long life. Effective in high speed machining and dry machining as coating properties-Can be reground. Please refer to the "Regrinding Service" page for application procedures, range of services, prices, etc.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    1 ~ 6BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]5 ~ 223For High Hardness (Silicon Group)50 ~ 11017 ~ 726 ~ 12
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TSC series carbide ball end mill, short model
                    • Volume Discount
                    • TS
                    • General Steel
                    • 4 Flutes
                    • S (Short)

                    MISUMI

                    TSC series carbide ball end mill, short model

                    [Features] -The surface of the workpiece is very good after machining.-It has a coating with high oxidation resistance and high hardness, and achieves long service life. Effective in high-speed machining and dry machining as coating properties-Can be reground. Please refer to the "Regrinding Service" page for application procedures, performance range, prices, etc.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    1 ~ 10BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]3 ~ 254For High Hardness (Silicon Group)50 ~ 15015 ~ 756 ~ 20
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TSC series carbide ball end mill, 4-flute / regular model
                    • Volume Discount
                    • TS
                    • General Steel
                    • 4 Flutes
                    • R (Regular)

                    MISUMI

                    TSC series carbide ball end mill, 4-flute / regular model

                    [Features] -The surface of the workpiece is very good after machining.-It has coating with high oxidation resistance and high hardness, and achieves long service life. As a coating property, it is effective in high-speed machining and dry machining.-Can be reground. Please refer to the "Regrinding Service" page for application methods, range of services, prices, etc.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    1.5 ~ 6BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○]5 ~ 224For High Hardness (Silicon Group)60 ~ 11017 ~ 726 ~ 12
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • Carbide ball end mill, 2-flute / short model
                    • Volume Discount
                    • Non-Coated
                    • General Steel
                    • 2 Flutes
                    • S (Short)

                    MISUMI

                    Carbide ball end mill, 2-flute / short model

                    Highly versatile due to the non-coated specification
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.2 ~ 10BallGeneral Steel[◎] / Quenched and tempered steel[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○] / Resin[○]0.8 ~ 252Non-Coated40 ~ 150-3 ~ 20
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TS Coated Carbide Ball End Mill, Cutting Edge Rigidity Machining / For High-Hardness Steel Machining, 2-Flute / No Side Blade
                    • Volume Discount
                    • TS
                    • High-Hardness Steel
                    • 2 Flutes

                    MISUMI

                    TS Coated Carbide Ball End Mill, Cutting Edge Rigidity Machining / For High-Hardness Steel Machining, 2-Flute / No Side Blade

                    [Features] -Ultra-fine-grained carbide base material suitable for machining high hardness steels is used (according to the manufacturer's cutting test results).-MIAutomatic steelI-Original shape with rigid cutting edge treatment and no side cutting edge. High strength of the tool and cutting edge, resulting in a stable cutting edge shape and long tool life in high-speed milling-Can be reground. Please refer to the "Regrinding Service" page for information on application methods, range of services, prices, etc.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    1 ~ 5BallGeneral Steel[○] / Quenched and tempered steel[○] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[◎] / Stainless Steel[○] / Cast Iron[◎]1 ~ 52For High Hardness (Silicon Group)50 ~ 905 ~ 106 ~ 10
                    Preço regular (excluindo IVA):
                    113.26 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TSC Series Carbide Ball End Mill (for Shrink Fit Holder) for High-Hardness Steel Machining, 2-Flute / Stub Model
                    • Volume Discount
                    • TS
                    • High-Hardness Steel
                    • 2 Flutes
                    • B (Stub)

                    MISUMI

                    TSC Series Carbide Ball End Mill (for Shrink Fit Holder) for High-Hardness Steel Machining, 2-Flute / Stub Model

                    The high precision ball end mill for shrink fit holder is ideal for the high-precision 3D machining of high-hardness steel
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.3 ~ 3BallGeneral Steel[○] / Quenched and tempered steel[○] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[◎] / Stainless Steel[○] / Cast Iron[◎]0.6 ~ 62For High Hardness (Silicon Group)40-6
                    Preço regular (excluindo IVA):
                    64.27 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • TSC Series Carbide Ball End Mill for Stainless Steel Machining, 2-Flute / Short Model
                    • Volume Discount
                    • TS
                    • SUS
                    • 2 Flutes
                    • S (Short)

                    MISUMI

                    TSC Series Carbide Ball End Mill for Stainless Steel Machining, 2-Flute / Short Model

                    Blade shape ball end mill that's suitable for work materials with low thermal conductivity such as the hard-to-cut SUS
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    1 ~ 5BallGeneral Steel[◎] / Quenched and tempered steel[○] / Stainless Steel[◎] / Cast Iron[○]3 ~ 152For High Hardness (Silicon Group)50 ~ 100-6 ~ 10
                    Preço regular (excluindo IVA):
                    103.49 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • DLC Coated Carbide Ball End Mill for Aluminum Machining, 2-Flute / Short Model
                    • Volume Discount
                    • DLC
                    • Aluminum
                    • 2 Flutes
                    • S (Short)

                    MISUMI

                    DLC Coated Carbide Ball End Mill for Aluminum Machining, 2-Flute / Short Model

                    The cutting performance of aluminum has been improved by the combination of sharp cutting edge and DLC coating
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.5 ~ 6BallAluminum[◎] / Copper[○] / Resin[○]1.5 ~ 182DLC50 ~ 11014 ~ 684 ~ 12
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • Carbide Ball End Mill for Aluminum Machining, 2-Flute / Short Model
                    • Volume Discount
                    • Non-Coated
                    • Aluminum
                    • 2 Flutes
                    • S (Short)

                    MISUMI

                    Carbide Ball End Mill for Aluminum Machining, 2-Flute / Short Model

                    A type for aluminum that achieves high efficiency while having the affordable uncoated design
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.5 ~ 6BallAluminum[◎] / Copper[○] / Graphite[○] / Resin[○]1.5 ~ 182Non-Coated50 ~ 11014 ~ 684 ~ 12
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • CRN Coated Ball End Mill for Copper Electrode Machining, 2-Flute / Short Model
                    • Volume Discount
                    • CrN
                    • Copper
                    • 2 Flutes
                    • S (Short)

                    MISUMI

                    CRN Coated Ball End Mill for Copper Electrode Machining, 2-Flute / Short Model

                    Ideal for copper electrode processing due to the CrN coating that exhibits excellent lubricity
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.5 ~ 6BallAluminum[○] / Copper[◎] / Resin[○]1.5 ~ 182CrN50 ~ 120-4 ~ 12
                    Preço regular (excluindo IVA):
                    35.08 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • Diamond Coated Carbide Ball End Mill for Graphite Machining, 2-Flute
                    • Volume Discount
                    • DIA
                    • Graphite
                    • 2 Flutes
                    • L (Long)

                    MISUMI

                    Diamond Coated Carbide Ball End Mill for Graphite Machining, 2-Flute

                    Diamond coated products that exert tremendous durability are available in the industry's lowest price
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.5 ~ 6BallAluminum[○] / Copper[○] / Graphite[◎] / Resin[○]3 ~ 552Dia Coat50 ~ 20020 ~ 654 ~ 12
                    Preço regular (excluindo IVA):
                    111.08 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • Diamond Coated Carbide Ball End Mill for Graphite Machining, 4-Flute / Short Model
                    • Volume Discount
                    • DIA
                    • Graphite
                    • 4 Flutes
                    • S (Short)

                    MISUMI

                    Diamond Coated Carbide Ball End Mill for Graphite Machining, 4-Flute / Short Model

                    4-flute ball for graphite that achieves high feed
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    1 ~ 6BallAluminum[○] / Copper[○] / Graphite[◎] / Resin[○]4 ~ 244Dia Coat50 ~ 80-6 ~ 12
                    Preço regular (excluindo IVA):
                    99.52 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • Carbide Ball End Mill for Graphite Machining, 2-Flute / Long Model
                    • Volume Discount
                    • Non-Coated
                    • Graphite
                    • 2 Flutes
                    • L (Long)

                    MISUMI

                    Carbide Ball End Mill for Graphite Machining, 2-Flute / Long Model

                    The price of the non-coated product with excellent cost performance has been further reduced
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    1 ~ 6BallAluminum[○] / Copper[○] / Graphite[◎] / Resin[○]10 ~ 552Non-Coated100 ~ 20020 ~ 654 ~ 12
                    Preço regular (excluindo IVA):
                    77.02 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • Carbide Ball End Mill for Resin Machining, 2-Flute / Short Model
                    • Volume Discount
                    • Non-Coated
                    • Resin
                    • 2 Flutes
                    • S (Short)

                    MISUMI

                    Carbide Ball End Mill for Resin Machining, 2-Flute / Short Model

                    Sharp edge that's suitable for machining resin
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.5 ~ 6BallAluminum[○] / Copper[○] / Graphite[○] / Resin[◎]1.5 ~ 182Non-Coated50 ~ 120-4 ~ 12
                    Preço regular (excluindo IVA):
                    30.26 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • CBN Ball End Mill, 2-Flute
                    • Volume Discount
                    • High-Hardness Steel
                    • 2 Flutes

                    MISUMI

                    CBN Ball End Mill, 2-Flute

                    CBN ball end mill that's ideal for precision finishing is available at a value price
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.3 ~ 1BallGeneral Steel[○] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[◎]0.5 ~ 1.22Non-Coated501.5 ~ 54
                    Preço regular (excluindo IVA):
                    138.36 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • MRC Series Carbide Ball End Mill, for Heat-Treated Steel Machining, 2-Flute / Regular Model
                    • Volume Discount
                    • MR
                    • General Steel
                    • 2 Flutes
                    • R (Regular)

                    MISUMI

                    MRC Series Carbide Ball End Mill, for Heat-Treated Steel Machining, 2-Flute / Regular Model

                    The user friendly regular flute length type is released simultaneously
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.2 ~ 8BallGeneral Steel[○] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[○] / High Hardness Steel: to HRC65[○] / Stainless Steel[○] / Cast Iron[◎]1.5 ~ 302MRC50 ~ 140-4 ~ 16
                    Preço regular (excluindo IVA):
                    22.05 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • XAL Series Carbide Ball End Mill, 2-Flute / Regular Model
                    • Volume Discount
                    • XAL
                    • General Steel
                    • 2 Flutes

                    MISUMI

                    XAL Series Carbide Ball End Mill, 2-Flute / Regular Model

                    The regular flute length type is introduced in the low-price and popular XAL balls
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.2 ~ 8BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[◎] / Aluminum[◎] / Copper[◎] / Resin[○]1.5 ~ 482For General Steels (AlCrN, etc.)50 ~ 140-4 ~ 16
                    Preço regular (excluindo IVA):
                    15.94 €
                    Data de envio regular:
                    5 dias úteis
                    Configurar
                  • GS MILL Long Neck Hard Ball GSBNH2
                    • Volume Discount

                    NACHI(FUJIKOSHI)

                    GS MILL Long Neck Hard Ball GSBNH2

                    Suitable for microfabrication of mold. A variety of size alignment allows for multiple types of machining.
                    Ler mais
                    R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                    0.5BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[○] / Stainless Steel[◎] / Cast Iron[○] / Titanium[○]1.52TiAlN45-4
                    Preço regular (excluindo IVA):
                    58.45 €
                    Data de envio regular:
                    6 dias úteis
                    Configurar
                  • CBN Mold Finish Master BNBP

                      NACHI(FUJIKOSHI)

                      CBN Mold Finish Master BNBP

                      -CBN ball nose end mill.-Suitable for high speed finishing of tools made of high hardness materials.
                      Ler mais
                      R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                      0.2 ~ 1BallQuenched and tempered steel[○] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[◎]0.3 ~ 1.42-501.2 ~ 5.54 ~ 6
                      Preço regular (excluindo IVA):
                      339.04 €
                      Data de envio regular:
                      6 dias úteis
                      Configurar
                    • DLC Mill, Ball 2DLCR
                      • Volume Discount

                      NACHI(FUJIKOSHI)

                      DLC Mill, Ball 2DLCR

                      End-mill for aluminum and copper alloys. Suitable for curved surface processing.
                      Ler mais
                      R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                      2.5BallAluminum[◎] / Copper[○]7.52DLC90146
                      Preço regular (excluindo IVA):
                      107.75 €
                      Data de envio regular:
                      6 dias úteis
                      Configurar
                    • Mold Meister Ball 2MMR
                      • Volume Discount

                      NACHI(FUJIKOSHI)

                      Mold Meister Ball 2MMR

                      Ideal for polishing of precision molds. R accuracy ± 3μm, R accuracy range 180 °
                      Ler mais
                      R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                      0.5 ~ 6BallGeneral Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / Stainless Steel[◎] / Cast Iron[○] / Titanium[○]1.5 ~ 182TiAlN50 ~ 120-4 ~ 12
                      Preço regular (excluindo IVA):
                      188.08 €
                      Data de envio regular:
                      6 dias úteis
                      Configurar
                    • 2-Flute, for Graphite, Ball End DG-EBD
                      • Volume Discount

                      OSG

                      2-Flute, for Graphite, Ball End DG-EBD

                      Diamond coating end-mill for aluminum processing. Promises wonderful elongation of tool life.
                      Ler mais
                      R Size(mm)Typework materialBlade length (ℓ)(mm)Number of flutes(sheet)CoatingOverall Length (L)(mm)Underneck length (ℓ1)(mm)Shank diameter (d)(mm)
                      2 ~ 6BallAluminum[○] / Graphite[◎] / Resin[◎]8 ~ 602DG80 ~ 200-4 ~ 12
                      Preço regular (excluindo IVA):
                      115.38 €
                      Data de envio regular:
                      6 dias úteis
                      Configurar

                    Produtos recentemente visualizados