Carbide Radius End Mills（R Precision：±0.02）
Search by sub-category
| Shipping Days |
|
|---|
?* Information on days to ship and prices
-
TSC series carbide radius end mill, 2-flute / regular model
MISUMI
[Features]
General 2-flute cutter with regular flute length and flute radius
-Radius cutting edge also effectively suppresses chipping
-Can be reground. Please refer to the "Regrinding Service" page for information on application procedures, range of services, prices, etc.- Volume Discount
- TS
- General Steel
- 2 Flutes
- R (Regular)
Configure nowMin. Shipping Days ： 13 Days -
XAL series carbide radius end mill, 4-flute / short model
MISUMI
The 4-flute type that simultaneously achieves improved efficiency and tool cost reduction can be selected from 17 sizes- Volume Discount
- XAL
- General Steel
- 4 Flutes
Configure nowStarting from∗ ： 18.89 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
XAL series carbide radius end mill, 3-flute, 45° torsion / regular model
MISUMI
3-flute 45° helix radius that's resistant to chattering is available at an affordable price- Volume Discount
- XAL
- General Steel
- 3 Flutes
Configure nowStarting from∗ ： 23.73 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
XAL series carbide radius end mill, 4-flute, 45° torsion / regular model
MISUMI
4-Flute Radius for High-Efficiency and High-Speed Machining- Volume Discount
- XAL
- General Steel
- 4 Flutes
Configure nowStarting from∗ ： 23.73 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
XAL series carbide radius end mill, 2-flute / short model
MISUMI
Radius end mills are available at low prices- Volume Discount
- XAL
- General Steel
- 2 Flutes
Configure nowStarting from∗ ： 14.52 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
TSC series carbide radius end mill, high-feed, high-rigidity, 4-flute / no side blade
MISUMI
[Features]
-High rigidity is achieved by using a negative radius and a short cutting edge length with no helix angle, and chatter is suppressed even in pocket corners
-Since the machine has a rear taper, it is possible to perform machining without the peripheral edge hitting the side when machining corners
-Even when machining the bottom side, a single machine can be used from middle finishing to final finishing, achieving a reduction in machining time.- Volume Discount
- TS
- High-Hardness Steel
- 4 Flutes
Configure nowStarting from∗ ： 61.48 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
TSC series carbide radius end mill, 2-flute / 1.5D Flute Length (stub) model
MISUMI
[Features]
-Short cutting edge length with cutting edge radius attached to the 2-flute general purpose cutters
-Radius cutting edge is also effective in suppressing chipping
-Can be reground. Please refer to the "Regrinding Service" page for application information, scope of service, pricing, etc.- Volume Discount
- TS
- General Steel
- 2 Flutes
- B (Stub)
Configure nowMin. Shipping Days ： 13 Days -
TSC series carbide radius end mill, 2-flute / short model
MISUMI
[Features]
-Short cutting edge length with cutting edge radius attached to the 2-flute general purpose cutters
-Radius cutting edge is also effective in suppressing chipping
-Can be reground. Please refer to the "Regrinding Service" page for application information, scope of service, pricing, etc.- Volume Discount
- TS
- General Steel
- 2 Flutes
- S (Short)
Configure nowMin. Shipping Days ： 13 Days -
TSC series carbide radius end mill, 4-flute / stub model
MISUMI
[Features]
-Designed with optimum blade length, shank length and overall length considering processing with shrink holder
-Can be resharpened. Please refer to the "Regrinding Service" page for information on possible applications, range of services, prices, etc.- Volume Discount
- TS
- General Steel
- 4 Flutes
- B (Stub)
Configure nowStarting from∗ ： 43.32 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
TSC series carbide radius end mill, 4-flute / stub model
MISUMI
[Features]
-Short cutting edge length with cutting edge radius fitted to a general purpose 4 flute cutter
-Radius cutting edge is also effective in suppressing chipping
-Can be reground. Please refer to the "Regrinding Service" page for information on procedures, scope of services, prices, etc.- Volume Discount
- TS
- General Steel
- 4 Flutes
- B (Stub)
Configure nowMin. Shipping Days ： 13 Days -
TSC series carbide radius end mill, 4-flute / short model
MISUMI
[Features]
-Short cutting edge length with cutting edge radius attached to a general purpose cutter with 4 cutting edges
-Radius cutting edge is also effective in suppressing chipping
-Can be reground. Please refer to the "Regrinding Service" page for information on procedures, scope of services, prices, etc.- Volume Discount
- TS
- General Steel
- 4 Flutes
- S (Short)
Configure nowMin. Shipping Days ： 13 Days -
TSC series carbide radius end mill, 4-flute / regular model
MISUMI
[Features]
-Regular cutting edge length with cutting edge radius fitted to a general purpose cutter with 4 cutting edges
-Radius cutting edge is also effective in suppressing chipping
-Can be reground. Please refer to the "Regrinding Service" page for information on application procedures, range of services, prices, etc.- Volume Discount
- TS
- General Steel
- 4 Flutes
- R (Regular)
Configure nowMin. Shipping Days ： 13 Days -
TSC series carbide radius end mill, 3-flute, 45° spiral, stub / tapered neck model
MISUMI
By the adoption of 3-blade shape and tapered neck, chattering is suppressed in deep engraving- Volume Discount
- TS
- High-Hardness Steel
- 3 Flutes
- B (Stub)
Configure nowStarting from∗ ： 83.63 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
TSC series carbide radius end mill, 4-flute, 45° spiral, stub / tapered neck model
MISUMI
[Features]
-High rigidity and cutting sharpness are achieved by the combination of negative blade radius, suitable core diameter and 45° helix angle, enabling highly efficient high feed machining
-Conical neck effectively suppresses chatter
-Variable design that can be used for engraving, side face, rough and medium grinding
-Can be reground. Please refer to the "Regrinding Service" page for application procedures, range of services, prices, etc.- Volume Discount
- TS
- High-Hardness Steel
- 4 Flutes
- B (Stub)
Configure nowStarting from∗ ： 97.30 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
TSC Series Carbide Radius End Mill for High-Hardness Copper Machining, Multi-Blade, Spiral / Stub Model
MISUMI
[Features]
-High helix angle and radius end mill for machining high hardness steel
-High tool rigidity minimises tool tilt when side milling
-Machining high hardness steel up to 65HRC is possible
-Can be reground. Please refer to the "Regrinding Service" page for information on application methods, range of services, prices, etc.- Volume Discount
- TS
- High-Hardness Steel
- Multi-Flutes （5 ~）
- B (Stub)
Configure nowMin. Shipping Days ： 5 Days -
TSC series carbide radius end mill, 3-flute, 45° spiral / short model
MISUMI
The popular radius type for stainless steel processing is also effective in preventing chipping- Volume Discount
- TS
- SUS
- 3 Flutes
- S (Short)
Configure nowStarting from∗ ： 96.98 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
DLC Coated Carbide Radius End Mill for Aluminum Machining, 2-Flute / Regular Model
MISUMI
In addition to the standard products, the radius can be selected extensively for manufactured products- Volume Discount
- DLC
- Aluminum
- 2 Flutes
- R (Regular)
Configure nowStarting from∗ ： 69.07 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
DLC Coated Carbide Radius End Mill for Aluminum Machining, 3-Flute / Regular Flute Length Model
MISUMI
The radius-equipped type prevents cutter marks and also shows effectiveness in improving the surface roughness- Volume Discount
- DLC
- Aluminum
- 3 Flutes
- R (Regular)
Configure nowMin. Shipping Days ： 5 Days -
Carbide Radius End Mill for Aluminum Machining, 2-Flute / Regular Model
MISUMI
Non-coated manufactured products can be shipped on the 5th day in addition to the stocked products- Volume Discount
- Non-Coated
- Aluminum
- 2 Flutes
- R (Regular)
Configure nowStarting from∗ ： 45.08 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
Carbide Radius End Mill for Aluminum Machining, 3-Flute / Regular Flute Length Model
MISUMI
Radius type that's also effective in preventing cutter marks- Volume Discount
- Non-Coated
- Aluminum
- 3 Flutes
- R (Regular)
Configure nowStarting from∗ ： 68.94 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
Carbide Radius End Mill for Aluminum Machining, 3-Flute / Stub, Long Shank Model
MISUMI
Comes with the rounded edge that suppresses machining streaks in standing-wall multi-stage machining- Volume Discount
- Non-Coated
- Aluminum
- 3 Flutes
Configure nowStarting from∗ ： 105.17 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
Diamond Coated Carbide Radius End Mill for Graphite Machining, 4-Flute / Long Model
MISUMI
The diamond coated radius shape that's ideal for shaping graphite- Volume Discount
- DIA
- Graphite
- 4 Flutes
- Long
Configure nowStarting from∗ ： 166.75 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
Carbide Radius End Mill for Resin Machining, 2-Flute / Regular Model
MISUMI
Small radius type that prevents cutter marks on resin- Volume Discount
- Non-Coated
- Resin
- 2 Flutes
- R (Regular)
Configure nowStarting from∗ ： 42.65 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
Non-Coated TS Coated Carbide 0.1 mm Unit Radius Designated End Mill
MISUMI
[Features]
-Alteration cutter that can determine the radius of the carbide cutter in 0.1 mm increments
-Can be reground. Please refer to the "Regrinding service" page for information on possible applications, range of services, prices, etc.- Non-Coated
- General Steel
Configure nowMin. Shipping Days ： 7 Days -
XAL Coated Carbide Radius End Mill, 4-Flute, 45° Torsion / Short Model
MISUMI
Introducing the short type in the 4-flute radius for high-efficiency and high-speed machining- Volume Discount
Configure nowStarting from∗ ： 17.06 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
TSC Series Carbide Uneven Lead 4-Flute Radius End Mill
MISUMI
Introducing the long-awaited unequal lead 4-flute radius end mill in the TSC series (helix angle of 40° / 43°)- Volume Discount
Configure nowStarting from∗ ： 45.45 € Min. Shipping Days ： 5 Days *Unit price with basic configuration
-
Radius End Mill 2-Flute
ATOM
Simultaneously machines rounded corners and straight base surfaces. High precision radius shape smoothly connects the straight part with the rounded part.- Volume Discount
Configure nowStarting from∗ ： 79.91 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
| Brand |
|---|
| Product Series |
| Starting from∗ |
| Min. Shipping Days |
| Specifications |
| Blade diameter (D)(φ) |
| R Size(mm) |
| work material |
| Blade length (ℓ)(mm) |
| Number of flutes(sheet) |
| Type |
| Overall Length (L)(mm) |
| Shank diameter (d)(mm) |
| Underneck length (ℓ1)(mm) |
| Machining Application |
| Coating |
| Torsion Angle (θ) |
| R Precision(μm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Brand | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | MISUMI | ATOM |
| Product Series | XAL series carbide radius end mill, 3-flute, 45° torsion / regular model | XAL series carbide radius end mill, 4-flute, 45° torsion / regular model | TSC series carbide radius end mill, high-feed, high-rigidity, 4-flute / no side blade | TSC series carbide radius end mill, 2-flute / 1.5D Flute Length (stub) model | TSC series carbide radius end mill, 3-flute, 45° spiral, stub / tapered neck model | TSC series carbide radius end mill, 4-flute, 45° spiral, stub / tapered neck model | TSC series carbide radius end mill, 3-flute, 45° spiral / short model | DLC Coated Carbide Radius End Mill for Aluminum Machining, 2-Flute / Regular Model | DLC Coated Carbide Radius End Mill for Aluminum Machining, 3-Flute / Regular Flute Length Model | Carbide Radius End Mill for Aluminum Machining, 2-Flute / Regular Model | Carbide Radius End Mill for Aluminum Machining, 3-Flute / Regular Flute Length Model | Carbide Radius End Mill for Aluminum Machining, 3-Flute / Stub, Long Shank Model | Diamond Coated Carbide Radius End Mill for Graphite Machining, 4-Flute / Long Model | Carbide Radius End Mill for Resin Machining, 2-Flute / Regular Model | Non-Coated TS Coated Carbide 0.1 mm Unit Radius Designated End Mill | XAL Coated Carbide Radius End Mill, 4-Flute, 45° Torsion / Short Model | |||||||||||
| Starting from∗ | - Volume Discount | 18.89 € *Unit price with basic configuration Volume Discount | 23.73 € *Unit price with basic configuration Volume Discount | 23.73 € *Unit price with basic configuration Volume Discount | 14.52 € *Unit price with basic configuration Volume Discount | 61.48 € *Unit price with basic configuration Volume Discount | - Volume Discount | - Volume Discount | 43.32 € *Unit price with basic configuration Volume Discount | - Volume Discount | - Volume Discount | - Volume Discount | 83.63 € *Unit price with basic configuration Volume Discount | 97.30 € *Unit price with basic configuration Volume Discount | - Volume Discount | 96.98 € *Unit price with basic configuration Volume Discount | 69.07 € *Unit price with basic configuration Volume Discount | - Volume Discount | 45.08 € *Unit price with basic configuration Volume Discount | 68.94 € *Unit price with basic configuration Volume Discount | 105.17 € *Unit price with basic configuration Volume Discount | 166.75 € *Unit price with basic configuration Volume Discount | 42.65 € *Unit price with basic configuration Volume Discount | - | 17.06 € *Unit price with basic configuration Volume Discount | 45.45 € *Unit price with basic configuration Volume Discount | 79.91 € *Unit price with basic configuration Volume Discount |
| Min. Shipping Days | 13 Days | 5 Days | 5 Days | 5 Days | 5 Days | 5 Days | 13 Days | 13 Days | 5 Days | 13 Days | 13 Days | 13 Days | 5 Days | 5 Days | 5 Days | 5 Days | 5 Days | 5 Days | 5 Days | 5 Days | 5 Days | 5 Days | 5 Days | 7 Days | 5 Days | 5 Days | 6 Days |
| Specifications |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| Blade diameter (D)(φ) | 2.5 ～ 20 | 3 ～ 20 | 3 ～ 12 | 4 ～ 12 | 1 ～ 12 | 3 ～ 12 | 3.5 ～ 8 | 2.5 ～ 20 | 2 ～ 12 | 3 ～ 12 | 3 ～ 12 | 3 ～ 12 | 3 ～ 12 | 3 ～ 12 | 6 ～ 12 | 3 ～ 12 | 2 ～ 12 | 2 ～ 12 | 2 ～ 12 | 2 ～ 12 | 5 ～ 22 | 6 ～ 12 | 1 ～ 10 | 1 ～ 20 | 2 ～ 20 | 2 ～ 25 | 1 ～ 6 |
| R Size(mm) | 0.1 ～ 3 | 0.1 ～ 3 | 0.2 ～ 2 | 0.2 ～ 2 | 0.1 ～ 3 | 0.75 ～ 3 | 0.1 ～ 3 | 0.1 ～ 3 | 0.3 ～ 1 | 0.1 ～ 3 | 0.1 ～ 3 | 0.1 ～ 3 | 0.8 ～ 2 | 0.8 ～ 2 | 0.5 ～ 2 | 0.5 ～ 2 | 0.2 ～ 1 | 0.2 ～ 1 | 0.2 ～ 1 | 0.2 ～ 1 | 0.5 ～ 2 | 0.5 ～ 3 | 0.2 | 0.1 ～ 3 | 0.2 ～ 3 | 0.2 ～ 6.5 | 0.1 ～ 0.3 |
| work material | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[◎] / Aluminum[◎] / Copper[◎] / Resin[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[◎] / Aluminum[◎] / Copper[◎] / Resin[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[◎] / Aluminum[◎] / Copper[◎] / Resin[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[◎] / Aluminum[◎] / Copper[◎] / Resin[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[○] / Stainless Steel[○] / Cast Iron[◎] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[○] / Stainless Steel[○] / Cast Iron[◎] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[○] / Stainless Steel[○] / Cast Iron[◎] | General Steel[○] / Quenched and tempered steel[○] / High Hardness Steel: to HRC55[◎] / High Hardness Steel: to HRC60[◎] / High Hardness Steel: to HRC65[◎] / Stainless Steel[○] / Cast Iron[◎] | General Steel[◎] / Quenched and tempered steel[○] / Stainless Steel[◎] / Aluminum[○] / Copper[○] | Aluminum[◎] / Copper[○] / Resin[○] | Aluminum[◎] / Copper[○] / Resin[○] | Aluminum[◎] / Copper[○] / Graphite[○] / Resin[○] | Aluminum[◎] / Copper[○] / Graphite[○] / Resin[○] | Aluminum[◎] / Copper[○] / Graphite[○] / Resin[○] | Aluminum[◎] / Copper[○] / Graphite[◎] / Resin[○] | Aluminum[○] / Copper[○] / Graphite[○] / Resin[◎] | General Steel[◎] / Quenched and tempered steel[○/◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[○] / Aluminum[○] / Copper[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[○] / Cast Iron[◎] / Aluminum[◎] / Copper[◎] / Resin[○] | General Steel[◎] / Quenched and tempered steel[◎] / High Hardness Steel: to HRC55[○] / Stainless Steel[◎] / Cast Iron[○] / Aluminum[○] / Titanium[○] / Copper[○] | General Steel[○] / Quenched and tempered steel[○] / Stainless Steel[○] / Aluminum[◎] / Resin[◎] |
| Blade length (ℓ)(mm) | 7.5 ～ 60 | 8 ～ 38 | 16 ～ 38 | 18 ～ 38 | 3 ～ 30 | 1.2 ～ 5 | 5.25 ～ 12 | 5 ～ 40 | 3 ～ 18 | 4.5 ～ 18 | 6 ～ 24 | 9 ～ 36 | 4.5 ～ 18 | 4.5 ～ 18 | 5 ～ 12 | 7 ～ 18 | 6 ～ 36 | 5 ～ 36 | 6 ～ 36 | 6 ～ 36 | 9 ～ 33 | 30 ～ 60 | 3 ～ 30 | 4 ～ 60 | 4 ～ 45 | 4 ～ 50 | 3 ～ 15 |
| Number of flutes(sheet) | 2 | 4 | 3 | 4 | 2 | 4 | 2 | 2 | 4 | 4 | 4 | 4 | 3 | 4 | 6 | 3 | 2 | 3 | 2 | 3 | 3 | 4 | 2 | 2 ～ 4 | 4 | 4 | 2 |
| Type | Radius | Radius | Radius | Radius | Radius | High-Feed Radius | Radius | Radius | Radius | Radius | Radius | Radius | Tapered neck radius | Tapered neck radius | Radius | Radius | Radius | Radius | Radius | Radius | Radius | Radius | Radius | Radius | Radius | Radius | Radius |
| Overall Length (L)(mm) | 45 ～ 125 | 50 ～ 100 | 60 ～ 100 | 60 ～ 100 | 50 ～ 75 | 60 ～ 110 | 40 ～ 60 | 40 ～ 110 | 35 ～ 60 | 45 ～ 75 | 45 ～ 75 | 45 ～ 85 | 80 ～ 160 | 80 ～ 160 | 60 ～ 85 | 60 ～ 100 | 40 ～ 80 | 40 ～ 80 | 40 ～ 80 | 40 ～ 80 | 80 ～ 200 | 150 ～ 200 | 50 ～ 80 | 40 ～ 125 | 50 ～ 110 | 50 ～ 120 | 45 ～ 60 |
| Shank diameter (d)(mm) | 4 ～ 20 | 4 ～ 20 | 6 ～ 12 | 6 ～ 12 | 4 ～ 12 | 6 ～ 12 | 6 ～ 8 | 4 ～ 20 | 4 ～ 12 | 6 ～ 12 | 6 ～ 12 | 6 ～ 12 | 6 ～ 16 | 6 ～ 16 | 6 ～ 12 | 6 ～ 12 | 4 ～ 12 | 4 ～ 12 | 4 ～ 12 | 4 ～ 12 | 4 ～ 20 | 6 ～ 12 | 3 ～ 10 | 4 ～ 20 | 4 ～ 20 | 6 ～ 25 | 4 ～ 6 |
| Underneck length (ℓ1)(mm) | - | - | - | - | - | 7.5 ～ 24 | - | - | - | - | - | - | 24 ～ 105 | 24 ～ 105 | 11 ～ 55 | - | - | 23 ～ 50 | - | - | - | 60 ～ 85 | - | - | - | - | - |
| Machining Application | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Inclined Cuts | Plane / Side / Curved surface / Groove / Plunging (Z feed) / Inclined Cuts | Plane / Side / Curved surface / Inclined Cuts | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Inclined Cuts | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Inclined Cuts | Plane / Side / Curved surface / Inclined Cuts | Plane / Side / Curved surface / Inclined Cuts | Plane / Side / Curved surface / Inclined Cuts | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Inclined Cuts | Plane / Side / Curved surface | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Groove / Plunging (Z feed) / Inclined Cuts | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Groove / Plunging (Z feed) / Inclined Cuts | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Inclined Cuts | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Groove / Inclined Cuts | Plane / Side / Curved surface / Inclined Cuts | Plane / Side / Curved surface / Groove | Plane / Side / Curved surface |
| Coating | For High Hardness (Silicon Group) | For General Steels (AlCrN, etc.) | For General Steels (AlCrN, etc.) | For General Steels (AlCrN, etc.) | For General Steels (AlCrN, etc.) | For High Hardness (Silicon Group) | For High Hardness (Silicon Group) | For High Hardness (Silicon Group) | For High Hardness (Silicon Group) | For High Hardness (Silicon Group) | For High Hardness (Silicon Group) | For High Hardness (Silicon Group) | For High Hardness (Silicon Group) | For High Hardness (Silicon Group) | For High Hardness (Silicon Group) | For High Hardness (Silicon Group) | DLC | DLC | Non-Coated | Non-Coated | Non-Coated | Dia Coat | Non-Coated | For High Hardness (Silicon Group) / Non-Coated | For General Steels (AlCrN, etc.) | For High Hardness (Silicon Group) | Non-Coated |
| Torsion Angle (θ) | Standard Helix (30˚ to 40˚) | Standard Helix (30˚ to 40˚) | High Helix (45˚ to 60˚) | High Helix (45˚ to 60˚) | Standard Helix (30˚ to 40˚) | No torsion | Standard Helix (30˚ to 40˚) | Standard Helix (30˚ to 40˚) | Standard Helix (30˚ to 40˚) | Standard Helix (30˚ to 40˚) | Standard Helix (30˚ to 40˚) | Standard Helix (30˚ to 40˚) | High Helix (45˚ to 60˚) | High Helix (45˚ to 60˚) | High Helix (45˚ to 60˚) | High Helix (45˚ to 60˚) | High Helix (45˚ to 60˚) | High Helix (45˚ to 60˚) | High Helix (45˚ to 60˚) | High Helix (45˚ to 60˚) | High Helix (45˚ to 60˚) | Standard Helix (30˚ to 40˚) | Standard Helix (30˚ to 40˚) | Standard Helix (30˚ to 40˚) | High Helix (45˚ to 60˚) | Other | Standard Helix (30˚ to 40˚) |
| R Precision(μm) | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 | ±0.02 |
Loading...
Filter by:
-
Blade diameter (D)(φ)
-
R Size(mm)
-
work material
-
Blade length (ℓ)(mm)
- 0.08
- 0.13
- 0.15
- 0.16
- 0.2
- 0.24
- 0.25
- 0.28
- 0.3
- 0.32
- 0.4
- 0.48
- 0.5
- 0.55
- 0.56
- 0.6
- 0.64
- 0.65
- 0.7
- 0.72
- 0.75
- 0.8
- 0.9
- 0.96
- 1
- 1.2
- 1.44
- 1.5
- 1.6
- 1.8
- 2
- 2.1
- 2.2
- 2.25
- 2.3
- 2.4
- 2.5
- 2.7
- 3
- 3
- 3.2
- 3.5
- 3.7
- 4
- 4
- 4.5
- 4.8
- 5
- 5
- 5.25
- 5.5
- 5.6
- 6
- 6
- 6.75
- 7
- 7.5
- 8
- 8.25
- 8.4
- 9
- 10
- 10
- 10.5
- 11
- 12
- 12
- 12.5
- 13
- 13.5
- 14
- 15
- 15
- 16
- 16.5
- 17
- 17.5
- 18
- 19
- 19.5
- 20
- 21
- 22
- 24
- 25
- 25.5
- 26
- 27
- 28
- 30
- 32
- 33
- 34
- 35
- 36
- 37.5
- 38
- 40
- 42
- 45
- 48
- 50
- 55
- 56
- 60
- 64
- 75
- 80
- 100
[5-36/1mm Unit(s)]
-
Number of flutes(sheet)
-
Type
- Radius
- High-Feed Radius
- Long-Neck Radius
- Tapered neck radius
-
Overall Length (L)(mm)
-
Shank diameter (d)(mm)
-
Underneck length (ℓ1)(mm)
-
Machining Application
-
Coating
-
Torsion Angle (θ)
-
R Precision(μm)
Brand
-
- ATOM (1)
- OKAZAKI SEIKO (0)
- DIJET (0)
- SPEED TIGER (0)
- KYOWA SEIKO (0)
- SANDVIK (0)
- WATERMILLS (0)
- UNION TOOL (0)
- VAN_HOORN (0)
- NS TOOL (0)
- SANKO MFG (0)
- TAIYO-TOOL (0)
- NACHI(FUJIKOSHI) (0)
- 7 LEADERS (0)
- OSG (0)
- THE CUT (0)
- GUHRING (0)
CAD data type
-
- 2D
- 3D
Categories related to Carbide Radius End Mills
Método de pagamento
Pagamento por conta
Pré-pagamento
Fabrico a pedido
Certificados
Copyright © MISUMI Corporation Todos os direitos reservados.