OMRON PLC (Input/Output Units)（Representative Standard：CUL）
| Shipping Days |
|
|---|
?* Information on days to ship and prices
-
NX Series Position Interface Pulse Output Unit NX-PG0□□□
OMRON
Positioning control with pulse outputs to command stepper motor drives and other pulse input motor drives
■ Features
· The MC Function Module of the NJ/NX/NY5 Controller allows you to
connect with as many axes as the NJ/NX/NY5 Controller can control
· High-speed remote I/O control with communications cycle as fast as 125 μs*1
· Multiple stepping motors and servo motors can be operated in synchronization by
using synchronous I/O refreshing or task period prioritized refreshing*2
· Latching (2 external latch inputs)
· Open collector pulse outputs up to 500 kHz
or line driver pulse outputs up to 4 MHz
· Line driver output models with 2 or 4 channels
*1 When using the NX-EC01□□ together with the NX701-□□□□ and NX-ECC203.
* *2 Task period prioritized refreshing is available when the NX-ECC203 is used together.Starting from∗ ： 463.67 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Starting from∗ ： 371.47 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
Starting from∗ ： 628.00 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
NX Series Digital Output Unit NX-OD Transistor Output Unit
OMRON
Digital output unit that is available in many variations, from high-speed types that enable high-speed synchronization control to general-purpose types
■ Features
· Can be mounted on an EtherCAT coupler to enable high-speed I/O refreshing
· Enables I/O refreshing synchronized with the controller control period (synchronous refresh)
· Using this unit in combination with an NX Series CPU Unit or EtherCAT Coupler Unit, an NX unit that uses a time stamping input method,
and an NX unit that uses a time-specific output method enables highly precise I/O control that does not depend on the
controller's control period
· The use of a removable terminal block improves system maintainability
· The Push-In Plus terminal block (screwless clamp terminal block) and connector type (MIL connector / Fujitsu connector)
greatly reduce the time required for wiring work
· A unit width of only 12 mm realizes space saving (connector type 30 mm)
· 2-, 4-, 8-, 16- and 32-output-contact types are available, enabling the I/O configuration that best suits your equipment
· Connect to the CJ Series using the EtherNet/IP couplerStarting from∗ ： 136.54 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Starting from∗ ： 1,402.67 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
Starting from∗ ： 371.47 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
Starting from∗ ： 318.67 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
Starting from∗ ： 806.67 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
Starting from∗ ： 784.67 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
Starting from∗ ： 1,318.00 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
Starting from∗ ： 2,193.33 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
Starting from∗ ： 445.60 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
NX Series Digital Output Unit NX-OC Relay Output Unit
OMRON
Digital output unit that is available in many variations, from high-speed types that enable high-speed synchronization control to general-purpose types
■ Features
· Can be mounted on an EtherCAT coupler to enable high-speed I/O refreshing
· Enables I/O refreshing synchronized with the controller control period (synchronous refresh)
· Using this unit in combination with an NX Series CPU Unit or EtherCAT Coupler Unit, an NX unit that uses a time stamping input method,
and an NX unit that uses a time-specific output method enables highly precise I/O control that does not depend on the
controller's control period
· The use of a removable terminal block improves system maintainability
· The Push-In Plus terminal block (screwless clamp terminal block) and connector type (MIL connector / Fujitsu connector)
greatly reduce the time required for wiring work
· A unit width of only 12 mm realizes space saving (connector type 30 mm)
· 2-, 4-, 8-, 16- and 32-output-contact types are available, enabling the I/O configuration that best suits your equipment
· Connect to the CJ Series using the EtherNet/IP couplerStarting from∗ ： 134.87 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
NX Series Digital Input Unit NX-ID DC Input Unit
OMRON
Digital input unit that is available in many variations, from high-speed types that enable high-speed synchronization control to general-purpose types
■ Features
· Can be mounted on an EtherCAT coupler to enable high-speed I/O refreshing
· Enables I/O refreshing synchronized with the controller control period (synchronous refresh)
· Using this unit in combination with an NX Series CPU Unit or EtherCAT Coupler Unit, an NX unit that uses a time-stamping input method,
and an NX unit that uses a time-specific output method enables highly precise I/O control that does not depend on the
controller's control period
· The use of a removable terminal block improves system maintainability
· The Push-In Plus terminal block (screwless clamp terminal block) and connector type (MIL connector / Fujitsu connector)
greatly reduce the time required for wiring work
· A unit width of only 12 mm realizes space saving (connector type 30 mm)
· 4-, 8-, 16- and 32-input-contact types are available, enabling the I/O configuration that best suits your equipment
· Connect to the CJ Series using the EtherNet/IP coupler- Volume Discount
Starting from∗ ： 163.21 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
NX Series Incremental Encoder Input Unit NX-EC0□□□
OMRON
Enables more precise timing control by synchronizing the encoder data with the time data
■ Features
· Open-collector-output type and line-driver-output type incremental encoders can be connected
· High-speed remote I/O control with communications cycle as fast as 125 μs*1
· Free-run refreshing, synchronous I/O refreshing, or
task period prioritized refreshing*2 with the NX1P2 CPU Unit or EtherCAT Coupler Unit
· The MC Function Module of the NJ/NX/NY5 Controllers allows the encoder
to be used as a motion axis
· Latching (1 internal signal and 2 input signals from external devices)
· Pulse period measurement
· 32-bit counters (80000000 to 7FFFFFFF HEX)
· Maximum counting rate: 4 MHz (Line receiver: 4 MHz; Open collector: 500 kHz)
· Time stamping
· Maximum and minimum counter value setting
· Connect to the CJ PLC using the EtherNet/IP coupler
*1 When using the NX-EC01□□ together with the NX701-□□□□ and NX-ECC203.
*2 Task period prioritized refreshing is available when the NX-ECC203 is used together.Starting from∗ ： 575.70 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
NX Series Safety I / O Unit NX-SI / SO
OMRON
Adds a Safety CPU Unit and Safety I/O Unit to an EtherCAT coupler to enable unified safety control
■ Features
· EN ISO 13849-1 (PLe / Safety Category 4), IEC 61508 (SIL3) certified
· Incorporating the Safety over EtherCAT (FSoE)* protocol enables both standard control and safety control on the same EtherCAT
· There are 2 types of Safety Input Unit: a 4-point type and an 8-point type, and 2 types of Safety Output Unit, a 2-point type and a 4-point type
· Safety units can be freely combined and placed with standard units
*The open protocol Safety over EtherCAT (abbreviated as FSoE; "FailSafe over EtherCAT") defines a
safety-related communication layer for EtherCAT.
Complies with the requirements of IEC 61508 (SIL3), enabling communication of safety data and standard data on the same communication system without
communication speed or cycle time restrictions.- Volume Discount
Starting from∗ ： 205.08 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
| Brand |
|---|
| Product Series |
| Starting from∗ |
| Min. Shipping Days ： |
| Number Of Inputs |
| Input Format |
| Rated Input Voltage(V) |
| Number of Outputs |
| Output Format |
| Rated load voltage(V) |
| Protection function |
| Connection Terminal |
| Representative Standard |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Brand | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON |
| Product Series | ||||||||||||||||
| Starting from∗ | 463.67 € *Unit price with basic configuration | 371.47 € *Unit price with basic configuration | 628.00 € *Unit price with basic configuration | 136.54 € *Unit price with basic configuration | 1,402.67 € *Unit price with basic configuration | 371.47 € *Unit price with basic configuration | 318.67 € *Unit price with basic configuration | 806.67 € *Unit price with basic configuration | 784.67 € *Unit price with basic configuration | 1,318.00 € *Unit price with basic configuration | 2,193.33 € *Unit price with basic configuration | 445.60 € *Unit price with basic configuration | 134.87 € *Unit price with basic configuration | 163.21 € *Unit price with basic configuration | 575.70 € *Unit price with basic configuration | 205.08 € *Unit price with basic configuration |
| Min. Shipping Days ： | 6 Days | 7 Days | 7 Days | 6 Days | 7 Days | 7 Days | 7 Days | 7 Days | 7 Days | 7 Days | 7 Days | 7 Days | 6 Days | 6 Days | 6 Days | 6 Days |
| Number Of Inputs | 32 | - | 16 ～ 96 | - | - | 8 ～ 64 | 1 ～ 8 | 16 | 16 ～ 32 | - | - | 10 | - | 16 | - | - |
| Input Format | DC input / Other | - | DC input / AC input / AC/DC input | - | - | AC input | DC input | - | - | - | - | - | - | DC input | Other | - |
| Rated Input Voltage(V) | 24 | - | 24 ～ 200 to 240 | DC24 | - | 24 ～ 200 to 240 | 12–24 | 24 | 5 ～ 24 | - | - | - | - | 24 | - | - |
| Number of Outputs | - | 8 ～ 64 | 8 ～ 64 | 16 ～ 32 | - | - | 1 | - | 16 ～ 32 | - | - | 6 | - | - | - | - |
| Output Format | Other | Relay contact output / Triac output / Transistor / source output / Transistor / sync output | Relay contact output / Triac output / Transistor / source output / Transistor / sync output | Transistor / source output / Other | - | - | - | - | Transistor / source output / Transistor / sync output | - | - | Transistor / sync output | Relay contact output | - | Other | Transistor / source output |
| Rated load voltage(V) | - | - | - | - | - | - | 5 | - | - | - | - | - | - | - | - | - |
| Protection function | - | Output protection function | - | Other | - | - | - | - | - | - | - | - | - | - | - | Other |
| Connection Terminal | Terminal Block / Connector | - | Terminal Block / Connector | Terminal Block | - | - | Terminal Block / Connector | - | - | - | - | - | Terminal Block | Terminal Block / Connector | Terminal Block | Terminal Block |
| Representative Standard | CUL | CUL | CUL | CUL | CUL | CUL | CUL | CUL | CUL | CUL | CUL | CUL | CUL | CUL | CUL | CUL |
Loading...
Filter by:
Narrow search by specifying spec./dim.
-
Number Of Inputs
-
Input Format
- DC input
- AC input
- AC/DC input
- Other
-
Rated Input Voltage(V)
-
Number of Outputs
-
Output Format
- Relay contact output
- Triac output
- Transistor / source output
- Transistor / sync output
- Other
-
Rated load voltage(V)
-
Protection function
- None
- Output protection function
- Other
-
Connection Terminal
- Terminal Block
- Connector
-
Representative Standard
- CE
- UL
- CUL
- TUV
- CSA
- Other
Narrow search by specifying Brand
-
- OMRON (16)
- WATANABE ELECTRIC INDUSTRY (0)
- PHOENIX CONTACT (0)
- SIEMENS (0)
- IFM ELECTRONIC (0)
- EATON (0)
Narrow search by specifying CAD data type
-
- 2D
- 3D
Categories related to PLC (Input/Output Units)
-
- PLC (CPU Units)
- PLC (Power Supply Units)
- PLC (Base Units)
- PLC (Software, Manuals)
- PLC Compatible Cables
- PLC Compatible Batteries
- PLC (Options, Others)
- PLC (Communication Units)
- PLC (Input/Output Units)
- PLC (Analog Units)
- PLC (Memory Units)
- PLC (Motion Controllers)
- PLC (Control Units)
- PLC (Wire-Saving Dedicated Units)
-
Método de pagamento
Pagamento por conta
Pré-pagamento
Fabrico a pedido
Certificados
Copyright © MISUMI Corporation Todos os direitos reservados.